There is no guarantee that the port state override registers have their default values, as not all switches support being reset via register or have a reset GPIO. So when forcing port config, we need to make sure to clear all fields, which we currently do not do for the speed and flow control configuration. This can cause flow control stay enabled, or in the case of speed becoming an illegal value, e.g. configured for 1G (0x2), then setting 100M (0x1), results in 0x3 which is invalid. For PORT_OVERRIDE_SPEED_2000M we need to make sure to only clear it on supported chips, as the bit can have different meanings on other chips, e.g. for BCM5389 this controls scanning PHYs for link/speed configuration. Fixes: 5e004460f874 ("net: dsa: b53: Add helper to set link parameters") Signed-off-by: Jonas Gorski --- drivers/net/dsa/b53/b53_common.c | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/drivers/net/dsa/b53/b53_common.c b/drivers/net/dsa/b53/b53_common.c index 2f846381d5a7..cb28256ef3cc 100644 --- a/drivers/net/dsa/b53/b53_common.c +++ b/drivers/net/dsa/b53/b53_common.c @@ -1372,6 +1372,10 @@ static void b53_force_port_config(struct b53_device *dev, int port, else reg &= ~PORT_OVERRIDE_FULL_DUPLEX; + reg &= ~(0x3 << GMII_PO_SPEED_S); + if (is5301x(dev) || is58xx(dev)) + reg &= ~PORT_OVERRIDE_SPEED_2000M; + switch (speed) { case 2000: reg |= PORT_OVERRIDE_SPEED_2000M; @@ -1390,6 +1394,11 @@ static void b53_force_port_config(struct b53_device *dev, int port, return; } + if (is5325(dev)) + reg &= ~PORT_OVERRIDE_LP_FLOW_25; + else + reg &= ~(PORT_OVERRIDE_RX_FLOW | PORT_OVERRIDE_TX_FLOW); + if (rx_pause) { if (is5325(dev)) reg |= PORT_OVERRIDE_LP_FLOW_25; -- 2.43.0 BCM63XX's switch does not support MDIO scanning of external phys, so its MACs needs to be manually configured for autonegotiated link speeds. So b53_force_port_config() and b53_force_link() accordingly also when mode is MLO_AN_PHY for those ports. Fixes lower speeds than 1000/full on rgmii ports 4 - 7. This aligns the behaviour with the old bcm63xx_enetsw driver for those ports. Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch") Signed-off-by: Jonas Gorski --- drivers/net/dsa/b53/b53_common.c | 12 +++++++++++- 1 file changed, 11 insertions(+), 1 deletion(-) diff --git a/drivers/net/dsa/b53/b53_common.c b/drivers/net/dsa/b53/b53_common.c index cb28256ef3cc..bb2c6dfa7835 100644 --- a/drivers/net/dsa/b53/b53_common.c +++ b/drivers/net/dsa/b53/b53_common.c @@ -1602,8 +1602,11 @@ static void b53_phylink_mac_link_down(struct phylink_config *config, struct b53_device *dev = dp->ds->priv; int port = dp->index; - if (mode == MLO_AN_PHY) + if (mode == MLO_AN_PHY) { + if (is63xx(dev) && in_range(port, B53_63XX_RGMII0, 4)) + b53_force_link(dev, port, false); return; + } if (mode == MLO_AN_FIXED) { b53_force_link(dev, port, false); @@ -1631,6 +1634,13 @@ static void b53_phylink_mac_link_up(struct phylink_config *config, if (mode == MLO_AN_PHY) { /* Re-negotiate EEE if it was enabled already */ p->eee_enabled = b53_eee_init(ds, port, phydev); + + if (is63xx(dev) && in_range(port, B53_63XX_RGMII0, 4)) { + b53_force_port_config(dev, port, speed, duplex, + tx_pause, rx_pause); + b53_force_link(dev, port, true); + } + return; } -- 2.43.0