stmmac_hw_setup() may return 0 on success and an appropriate negative integer as defined in errno.h file on failure, just check it and then return early if failed in stmmac_resume(). Signed-off-by: Tiezhu Yang Reviewed-by: Maxime Chevallier Reviewed-by: Huacai Chen --- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index f1abf4242cd2..b2d87d3e4a65 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -7975,7 +7975,14 @@ int stmmac_resume(struct device *dev) stmmac_free_tx_skbufs(priv); stmmac_clear_descriptors(priv, &priv->dma_conf); - stmmac_hw_setup(ndev, false); + ret = stmmac_hw_setup(ndev, false); + if (ret < 0) { + netdev_err(priv->dev, "%s: Hw setup failed\n", __func__); + mutex_unlock(&priv->lock); + rtnl_unlock(); + return ret; + } + stmmac_init_coalesce(priv); phylink_rx_clk_stop_block(priv->phylink); stmmac_set_rx_mode(ndev); -- 2.42.0 In order to use netdev_err() to print message in the callback function of fix_soc_reset(), change fix_soc_reset() to have "struct stmmac_priv *" as its first parameter. This is preparation for later patch, no functionality change. Suggested-by: Andrew Lunn Signed-off-by: Tiezhu Yang --- drivers/net/ethernet/stmicro/stmmac/dwmac-imx.c | 6 +++--- drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c | 2 +- drivers/net/ethernet/stmicro/stmmac/hwif.c | 2 +- include/linux/stmmac.h | 2 +- 4 files changed, 6 insertions(+), 6 deletions(-) diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-imx.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-imx.c index 889e2bb6f7f5..c2d9e89f0063 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-imx.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-imx.c @@ -49,7 +49,7 @@ struct imx_dwmac_ops { u32 flags; bool mac_rgmii_txclk_auto_adj; - int (*fix_soc_reset)(void *priv, void __iomem *ioaddr); + int (*fix_soc_reset)(struct stmmac_priv *priv, void __iomem *ioaddr); int (*set_intf_mode)(struct plat_stmmacenet_data *plat_dat); void (*fix_mac_speed)(void *priv, int speed, unsigned int mode); }; @@ -265,9 +265,9 @@ static void imx93_dwmac_fix_speed(void *priv, int speed, unsigned int mode) writel(old_ctrl, dwmac->base_addr + MAC_CTRL_REG); } -static int imx_dwmac_mx93_reset(void *priv, void __iomem *ioaddr) +static int imx_dwmac_mx93_reset(struct stmmac_priv *priv, void __iomem *ioaddr) { - struct plat_stmmacenet_data *plat_dat = priv; + struct plat_stmmacenet_data *plat_dat = priv->plat; u32 value = readl(ioaddr + DMA_BUS_MODE); /* DMA SW reset */ diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c index e1591e6217d4..bb376c69016d 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c @@ -509,7 +509,7 @@ static int loongson_dwmac_acpi_config(struct pci_dev *pdev, } /* Loongson's DWMAC device may take nearly two seconds to complete DMA reset */ -static int loongson_dwmac_fix_reset(void *priv, void __iomem *ioaddr) +static int loongson_dwmac_fix_reset(struct stmmac_priv *priv, void __iomem *ioaddr) { u32 value = readl(ioaddr + DMA_BUS_MODE); diff --git a/drivers/net/ethernet/stmicro/stmmac/hwif.c b/drivers/net/ethernet/stmicro/stmmac/hwif.c index 99635b37044a..3f7c765dcb79 100644 --- a/drivers/net/ethernet/stmicro/stmmac/hwif.c +++ b/drivers/net/ethernet/stmicro/stmmac/hwif.c @@ -100,7 +100,7 @@ int stmmac_reset(struct stmmac_priv *priv, void __iomem *ioaddr) return -EINVAL; if (plat && plat->fix_soc_reset) - return plat->fix_soc_reset(plat, ioaddr); + return plat->fix_soc_reset(priv, ioaddr); return stmmac_do_callback(priv, dma, reset, ioaddr); } diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h index 26ddf95d23f9..330694641a95 100644 --- a/include/linux/stmmac.h +++ b/include/linux/stmmac.h @@ -238,7 +238,7 @@ struct plat_stmmacenet_data { int (*set_clk_tx_rate)(void *priv, struct clk *clk_tx_i, phy_interface_t interface, int speed); void (*fix_mac_speed)(void *priv, int speed, unsigned int mode); - int (*fix_soc_reset)(void *priv, void __iomem *ioaddr); + int (*fix_soc_reset)(struct stmmac_priv *priv, void __iomem *ioaddr); int (*serdes_powerup)(struct net_device *ndev, void *priv); void (*serdes_powerdown)(struct net_device *ndev, void *priv); int (*mac_finish)(struct net_device *ndev, -- 2.42.0 If the MAC controller does not connect to any PHY interface, there is a missing clock, then the DMA reset fails. For this case, the DMA_BUS_MODE_SFT_RESET bit is 1 before software reset, just print an error message which gives a hint the PHY clock is missing, and then return -EINVAL immediately to avoid waiting for the timeout when the DMA reset fails in loongson_dwmac_fix_reset(). With this patch, for the normal end user, the computer start faster with reducing boot time for 2 seconds on the specified mainboard. Signed-off-by: Tiezhu Yang --- drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c index bb376c69016d..05f195a18548 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c @@ -513,6 +513,11 @@ static int loongson_dwmac_fix_reset(struct stmmac_priv *priv, void __iomem *ioad { u32 value = readl(ioaddr + DMA_BUS_MODE); + if (value & DMA_BUS_MODE_SFT_RESET) { + netdev_err(priv->dev, "the PHY clock is missing\n"); + return -EINVAL; + } + value |= DMA_BUS_MODE_SFT_RESET; writel(value, ioaddr + DMA_BUS_MODE); -- 2.42.0