With the phy_port representation intrduced, we can use .attach_port to populate the port information based on either the straps or the ti,fiber-mode property. This allows simplifying the probe function and allow users to override the strapping configuration. Signed-off-by: Maxime Chevallier --- drivers/net/phy/dp83822.c | 71 +++++++++++++++++++++++++-------------- 1 file changed, 45 insertions(+), 26 deletions(-) diff --git a/drivers/net/phy/dp83822.c b/drivers/net/phy/dp83822.c index 33db21251f2e..2657be2e9034 100644 --- a/drivers/net/phy/dp83822.c +++ b/drivers/net/phy/dp83822.c @@ -11,6 +11,7 @@ #include #include #include +#include #include #include @@ -811,17 +812,6 @@ static int dp83822_of_init(struct phy_device *phydev) int i, ret; u32 val; - /* Signal detection for the PHY is only enabled if the FX_EN and the - * SD_EN pins are strapped. Signal detection can only enabled if FX_EN - * is strapped otherwise signal detection is disabled for the PHY. - */ - if (dp83822->fx_enabled && dp83822->fx_sd_enable) - dp83822->fx_signal_det_low = device_property_present(dev, - "ti,link-loss-low"); - if (!dp83822->fx_enabled) - dp83822->fx_enabled = device_property_present(dev, - "ti,fiber-mode"); - if (!device_property_read_string(dev, "ti,gpio2-clk-out", &of_val)) { if (strcmp(of_val, "mac-if") == 0) { dp83822->gpio2_clk_out = DP83822_CLK_SRC_MAC_IF; @@ -950,6 +940,48 @@ static int dp83822_read_straps(struct phy_device *phydev) return 0; } +static int dp83822_attach_port(struct phy_device *phydev, struct phy_port *port) +{ + struct dp83822_private *dp83822 = phydev->priv; + int ret; + + if (port->mediums) { + if (phy_port_is_fiber(port)) + dp83822->fx_enabled = true; + } else { + ret = dp83822_read_straps(phydev); + if (ret) + return ret; + +#if IS_ENABLED(CONFIG_OF_MDIO) + if (dp83822->fx_enabled && dp83822->fx_sd_enable) + dp83822->fx_signal_det_low = + device_property_present(&phydev->mdio.dev, + "ti,link-loss-low"); + + /* ti,fiber-mode is still used for backwards compatibility, but + * has been replaced with the mdi node definition, see + * ethernet-port.yaml + */ + if (!dp83822->fx_enabled) + dp83822->fx_enabled = + device_property_present(&phydev->mdio.dev, + "ti,fiber-mode"); +#endif /* CONFIG_OF_MDIO */ + + if (dp83822->fx_enabled) { + port->lanes = 1; + port->mediums = BIT(ETHTOOL_LINK_MEDIUM_BASEF); + } else { + /* This PHY can only to 100BaseTX max, so on 2 lanes */ + port->lanes = 2; + port->mediums = BIT(ETHTOOL_LINK_MEDIUM_BASET); + } + } + + return 0; +} + static int dp8382x_probe(struct phy_device *phydev) { struct dp83822_private *dp83822; @@ -968,27 +1000,13 @@ static int dp8382x_probe(struct phy_device *phydev) static int dp83822_probe(struct phy_device *phydev) { - struct dp83822_private *dp83822; int ret; ret = dp8382x_probe(phydev); if (ret) return ret; - dp83822 = phydev->priv; - - ret = dp83822_read_straps(phydev); - if (ret) - return ret; - - ret = dp83822_of_init(phydev); - if (ret) - return ret; - - if (dp83822->fx_enabled) - phydev->port = PORT_FIBRE; - - return 0; + return dp83822_of_init(phydev); } static int dp83826_probe(struct phy_device *phydev) @@ -1172,6 +1190,7 @@ static int dp83822_led_hw_control_get(struct phy_device *phydev, u8 index, .led_hw_is_supported = dp83822_led_hw_is_supported, \ .led_hw_control_set = dp83822_led_hw_control_set, \ .led_hw_control_get = dp83822_led_hw_control_get, \ + .attach_port = dp83822_attach_port \ } #define DP83825_PHY_DRIVER(_id, _name) \ -- 2.49.0