Add hardware parameters for QCC2072, these parameters are directly taken
from WCN7850, with exceptions to hardware name, revision, firmware
directory, iova_mask and RFKILL parameter set.

Compared to WCN7850, QCC2072 doesn't require aligned IOVA when
transmitting packets, hence iova_mask is set to zero.

Besides, WCN7850 has a dedicated GPIO for RFKILL purpose, however QCC2072
has it coupled with WLAN_EN pin. For QCC2072, host is not allowed to send
any RFKILL configuration info to firmware, or firmware crashes. Hence
those parameters are all cleared to skip configuring command.

Tested-on: QCC2072 hw1.0 PCI WLAN.COL.1.0-01560-QCACOLSWPL_V1_TO_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3

Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
---
 drivers/net/wireless/ath/ath12k/wifi7/hw.c | 85 ++++++++++++++++++++++++++++++
 1 file changed, 85 insertions(+)

diff --git a/drivers/net/wireless/ath/ath12k/wifi7/hw.c b/drivers/net/wireless/ath/ath12k/wifi7/hw.c
index 1f5dda73230d..ef0a59f6339c 100644
--- a/drivers/net/wireless/ath/ath12k/wifi7/hw.c
+++ b/drivers/net/wireless/ath/ath12k/wifi7/hw.c
@@ -652,6 +652,91 @@ static const struct ath12k_hw_params ath12k_wifi7_hw_params[] = {
 
 		.dp_primary_link_only = true,
 	},
+	{
+		.name = "qcc2072 hw1.0",
+		.hw_rev = ATH12K_HW_QCC2072_HW10,
+
+		.fw = {
+			.dir = "QCC2072/hw1.0",
+			.board_size = 256 * 1024,
+			.cal_offset = 256 * 1024,
+			.m3_loader = ath12k_m3_fw_loader_driver,
+		},
+
+		.max_radios = 1,
+		.single_pdev_only = true,
+		.qmi_service_ins_id = ATH12K_QMI_WLFW_SERVICE_INS_ID_V01_WCN7850,
+		.internal_sleep_clock = true,
+
+		.hw_ops = &wcn7850_ops,
+		.ring_mask = &ath12k_wifi7_hw_ring_mask_wcn7850,
+
+		.host_ce_config = ath12k_wifi7_host_ce_config_wcn7850,
+		.ce_count = 9,
+		.target_ce_config = ath12k_wifi7_target_ce_config_wlan_wcn7850,
+		.target_ce_count = 9,
+		.svc_to_ce_map =
+			ath12k_wifi7_target_service_to_ce_map_wlan_wcn7850,
+		.svc_to_ce_map_len = 14,
+
+		.rxdma1_enable = false,
+		.num_rxdma_per_pdev = 2,
+		.num_rxdma_dst_ring = 1,
+		.rx_mac_buf_ring = true,
+		.vdev_start_delay = true,
+
+		.interface_modes = BIT(NL80211_IFTYPE_STATION) |
+				   BIT(NL80211_IFTYPE_AP) |
+				   BIT(NL80211_IFTYPE_P2P_DEVICE) |
+				   BIT(NL80211_IFTYPE_P2P_CLIENT) |
+				   BIT(NL80211_IFTYPE_P2P_GO),
+		.supports_monitor = true,
+
+		.idle_ps = true,
+		.download_calib = false,
+		.supports_suspend = true,
+		.tcl_ring_retry = false,
+		.reoq_lut_support = false,
+		.supports_shadow_regs = true,
+
+		.num_tcl_banks = 7,
+		.max_tx_ring = 3,
+
+		.mhi_config = &ath12k_wifi7_mhi_config_wcn7850,
+
+		.wmi_init = ath12k_wifi7_wmi_init_wcn7850,
+
+		.qmi_cnss_feature_bitmap = BIT(CNSS_QDSS_CFG_MISS_V01) |
+					   BIT(CNSS_PCIE_PERST_NO_PULL_V01),
+
+		.rfkill_pin = 0,
+		.rfkill_cfg = 0,
+		.rfkill_on_level = 0,
+
+		.rddm_size = 0x780000,
+
+		.def_num_link = 2,
+		.max_mlo_peer = 32,
+
+		.otp_board_id_register = 0,
+
+		.supports_sta_ps = true,
+
+		.acpi_guid = &wcn7850_uuid,
+		.supports_dynamic_smps_6ghz = false,
+
+		.iova_mask = 0,
+
+		.supports_aspm = true,
+
+		.ce_ie_addr = NULL,
+		.ce_remap = NULL,
+		.bdf_addr_offset = 0,
+
+		.current_cc_support = true,
+
+		.dp_primary_link_only = false,
+	},
 };
 
 /* Note: called under rcu_read_lock() */

-- 
2.25.1