From: "Ritesh Harjani (IBM)" <ritesh.list@gmail.com>

We brute force all possible blocksize & clustersize combinations on
a bigalloc filesystem for stressing atomic write using fio data crc
verifier. We run nproc * $LOAD_FACTOR threads in parallel writing to
a single $SCRATCH_MNT/test-file. With atomic writes this test ensures
that we never see the mix of data contents from different threads on
a given bsrange.

This test might do overlapping atomic writes but that should be okay
since overlapping parallel hardware atomic writes don't cause tearing as
long as io size is the same for all writes.

Signed-off-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Signed-off-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
---
 tests/ext4/061     | 130 +++++++++++++++++++++++++++++++++++++++++++++
 tests/ext4/061.out |   2 +
 2 files changed, 132 insertions(+)
 create mode 100755 tests/ext4/061
 create mode 100644 tests/ext4/061.out

diff --git a/tests/ext4/061 b/tests/ext4/061
new file mode 100755
index 00000000..a0e49249
--- /dev/null
+++ b/tests/ext4/061
@@ -0,0 +1,130 @@
+#! /bin/bash
+# SPDX-License-Identifier: GPL-2.0
+# Copyright (c) 2025 IBM Corporation. All Rights Reserved.
+#
+# FS QA Test 061
+#
+# Brute force all possible blocksize clustersize combination on a bigalloc
+# filesystem for stressing atomic write using fio data crc verifier. We run
+# nproc * 2 * $LOAD_FACTOR threads in parallel writing to a single
+# $SCRATCH_MNT/test-file. With fio aio-dio atomic write this test ensures that
+# we should never see the mix of data contents from different threads for any
+# given fio blocksize.
+#
+
+. ./common/preamble
+. ./common/atomicwrites
+
+_begin_fstest auto rw stress atomicwrites
+
+_require_scratch_write_atomic
+_require_aiodio
+
+FIO_LOAD=$(($(nproc) * 2 * LOAD_FACTOR))
+SIZE=$((100*1024*1024))
+fiobsize=4096
+
+# Calculate fsblocksize as per bdev atomic write units.
+bdev_awu_min=$(_get_atomic_write_unit_min $SCRATCH_DEV)
+bdev_awu_max=$(_get_atomic_write_unit_max $SCRATCH_DEV)
+fsblocksize=$(_max 4096 "$bdev_awu_min")
+
+function create_fio_configs()
+{
+	create_fio_aw_config
+	create_fio_verify_config
+}
+
+function create_fio_verify_config()
+{
+cat >$fio_verify_config <<EOF
+	[aio-dio-aw-verify]
+	direct=1
+	ioengine=libaio
+	rw=randwrite
+	bs=$fiobsize
+	fallocate=native
+	filename=$SCRATCH_MNT/test-file
+	size=$SIZE
+	iodepth=$FIO_LOAD
+	numjobs=$FIO_LOAD
+	atomic=1
+	group_reporting=1
+
+	verify_only=1
+	verify_state_save=0
+	verify=crc32c
+	verify_fatal=1
+	verify_write_sequence=0
+EOF
+}
+
+function create_fio_aw_config()
+{
+cat >$fio_aw_config <<EOF
+	[aio-dio-aw]
+	direct=1
+	ioengine=libaio
+	rw=randwrite
+	bs=$fiobsize
+	fallocate=native
+	filename=$SCRATCH_MNT/test-file
+	size=$SIZE
+	iodepth=$FIO_LOAD
+	numjobs=$FIO_LOAD
+	group_reporting=1
+	atomic=1
+
+	verify_state_save=0
+	verify=crc32c
+	do_verify=0
+
+EOF
+}
+
+# Let's create a sample fio config to check whether fio supports all options.
+fio_aw_config=$tmp.aw.fio
+fio_verify_config=$tmp.verify.fio
+fio_out=$tmp.fio.out
+
+create_fio_configs
+_require_fio $fio_aw_config
+
+for ((fsblocksize=$fsblocksize; fsblocksize <= $(_get_page_size); fsblocksize = $fsblocksize << 1)); do
+	# cluster sizes above 16 x blocksize are experimental so avoid them
+	# Also, cap cluster size at 128kb to keep it reasonable for large
+	# blocks size
+	fs_max_clustersize=$(_min $((16 * fsblocksize)) "$bdev_awu_max" $((128 * 1024)))
+
+	for ((fsclustersize=$fsblocksize; fsclustersize <= $fs_max_clustersize; fsclustersize = $fsclustersize << 1)); do
+		for ((fiobsize = $fsblocksize; fiobsize <= $fsclustersize; fiobsize = $fiobsize << 1)); do
+			MKFS_OPTIONS="-O bigalloc -b $fsblocksize -C $fsclustersize"
+			_scratch_mkfs_ext4  >> $seqres.full 2>&1 || continue
+			if _try_scratch_mount >> $seqres.full 2>&1; then
+				echo "== FIO test for fsblocksize=$fsblocksize fsclustersize=$fsclustersize fiobsize=$fiobsize ==" >> $seqres.full
+
+				touch $SCRATCH_MNT/f1
+				create_fio_configs
+
+				cat $fio_aw_config >> $seqres.full
+				echo >> $seqres.full
+				cat $fio_verify_config >> $seqres.full
+
+				$FIO_PROG $fio_aw_config >> $seqres.full
+				ret1=$?
+
+				$FIO_PROG $fio_verify_config >> $seqres.full
+				ret2=$?
+
+				_scratch_unmount
+
+				[[ $ret1 -eq 0 && $ret2 -eq 0 ]] || _fail "fio with atomic write failed"
+			fi
+		done
+	done
+done
+
+# success, all done
+echo Silence is golden
+status=0
+exit
diff --git a/tests/ext4/061.out b/tests/ext4/061.out
new file mode 100644
index 00000000..273be9e0
--- /dev/null
+++ b/tests/ext4/061.out
@@ -0,0 +1,2 @@
+QA output created by 061
+Silence is golden
-- 
2.49.0