This adds atomic write test using fio based on it's crc check verifier.
fio adds a crc for each data block. If the underlying device supports
atomic write then it is guaranteed that we will never have a mix data from
two threads writing on the same physical block.

Avoid doing overlapping parallel atomic writes because it might give
unexpected results. Use offset_increment=, size= fio options to achieve
this behavior.

Co-developed-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Signed-off-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Signed-off-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
---
 tests/generic/1226     | 107 +++++++++++++++++++++++++++++++++++++++++
 tests/generic/1226.out |   2 +
 2 files changed, 109 insertions(+)
 create mode 100755 tests/generic/1226
 create mode 100644 tests/generic/1226.out

diff --git a/tests/generic/1226 b/tests/generic/1226
new file mode 100755
index 00000000..efc360e1
--- /dev/null
+++ b/tests/generic/1226
@@ -0,0 +1,107 @@
+#! /bin/bash
+# SPDX-License-Identifier: GPL-2.0
+# Copyright (c) 2025 IBM Corporation. All Rights Reserved.
+#
+# FS QA Test 1226
+#
+# Validate FS atomic write using fio crc check verifier.
+#
+. ./common/preamble
+. ./common/atomicwrites
+
+_begin_fstest auto aio rw atomicwrites
+
+_require_scratch_write_atomic
+_require_odirect
+_require_aio
+
+_scratch_mkfs >> $seqres.full 2>&1
+_scratch_mount
+_require_xfs_io_command "falloc"
+
+touch "$SCRATCH_MNT/f1"
+awu_min_write=$(_get_atomic_write_unit_min "$SCRATCH_MNT/f1")
+awu_max_write=$(_get_atomic_write_unit_max "$SCRATCH_MNT/f1")
+
+blocksize=$(_max "$awu_min_write" "$((awu_max_write/2))")
+threads=$(_min "$(($(nproc) * 2 * LOAD_FACTOR))" "100")
+filesize=$((blocksize * threads * 100))
+depth=$threads
+io_size=$((filesize / threads))
+io_inc=$io_size
+testfile=$SCRATCH_MNT/test-file
+
+fio_config=$tmp.fio
+fio_out=$tmp.fio.out
+
+fio_aw_config=$tmp.aw.fio
+fio_verify_config=$tmp.verify.fio
+
+function create_fio_configs()
+{
+	create_fio_aw_config
+	create_fio_verify_config
+}
+
+function create_fio_verify_config()
+{
+cat >$fio_verify_config <<EOF
+	[verify-job]
+	direct=1
+	ioengine=libaio
+	rw=read
+	bs=$blocksize
+	filename=$testfile
+	size=$filesize
+	iodepth=$depth
+	group_reporting=1
+
+	verify_only=1
+	verify=crc32c
+	verify_fatal=1
+	verify_state_save=0
+	verify_write_sequence=0
+EOF
+}
+
+function create_fio_aw_config()
+{
+cat >$fio_aw_config <<EOF
+	[atomicwrite-job]
+	direct=1
+	ioengine=libaio
+	rw=randwrite
+	bs=$blocksize
+	filename=$testfile
+	size=$io_inc
+	offset_increment=$io_inc
+	iodepth=$depth
+	numjobs=$threads
+	group_reporting=1
+	atomic=1
+
+	verify_state_save=0
+	verify=crc32c
+	do_verify=0
+EOF
+}
+
+create_fio_configs
+_require_fio $fio_aw_config
+
+cat $fio_aw_config >> $seqres.full
+cat $fio_verify_config >> $seqres.full
+
+$XFS_IO_PROG -fc "falloc 0 $filesize" $testfile >> $seqres.full
+
+$FIO_PROG $fio_aw_config >> $seqres.full
+ret1=$?
+$FIO_PROG $fio_verify_config >> $seqres.full
+ret2=$?
+
+[[ $ret1 -eq 0 && $ret2 -eq 0 ]] || _fail "fio with atomic write failed"
+
+# success, all done
+echo Silence is golden
+status=0
+exit
diff --git a/tests/generic/1226.out b/tests/generic/1226.out
new file mode 100644
index 00000000..6dce0ea5
--- /dev/null
+++ b/tests/generic/1226.out
@@ -0,0 +1,2 @@
+QA output created by 1226
+Silence is golden
-- 
2.49.0