RTL8127ATF supports a SFP+ port for fiber modules (10GBASE-SR/LR/ER/ZR and DAC). The list of supported modes was provided by Realtek. According to the r8127 vendor driver also 1G modules are supported, but this needs some more complexity in the driver, and only 10G mode has been tested so far. Therefore mainline support will be limited to 10G for now. The SFP port signals are hidden in the chip IP and driven by firmware. Therefore mainline SFP support can't be used here. Signed-off-by: Heiner Kallweit --- drivers/net/ethernet/realtek/r8169_main.c | 89 ++++++++++++++++++++++- 1 file changed, 85 insertions(+), 4 deletions(-) diff --git a/drivers/net/ethernet/realtek/r8169_main.c b/drivers/net/ethernet/realtek/r8169_main.c index 755083852ee..cf37b4e6c4a 100644 --- a/drivers/net/ethernet/realtek/r8169_main.c +++ b/drivers/net/ethernet/realtek/r8169_main.c @@ -17,6 +17,7 @@ #include #include #include +#include #include #include #include @@ -733,6 +734,7 @@ struct rtl8169_private { unsigned supports_gmii:1; unsigned aspm_manageable:1; unsigned dash_enabled:1; + bool sfp_mode:1; dma_addr_t counters_phys_addr; struct rtl8169_counters *counters; struct rtl8169_tc_offsets tc_offset; @@ -1097,6 +1099,10 @@ static int r8168_phy_ocp_read(struct rtl8169_private *tp, u32 reg) if (rtl_ocp_reg_failure(reg)) return 0; + /* Return dummy MII_PHYSID2 in SFP mode to match SFP PHY driver */ + if (tp->sfp_mode && reg == (OCP_STD_PHY_BASE + 2 * MII_PHYSID2)) + return PHY_ID_RTL_DUMMY_SFP & 0xffff; + RTL_W32(tp, GPHY_OCP, reg << 15); return rtl_loop_wait_high(tp, &rtl_ocp_gphy_cond, 25, 10) ? @@ -1154,6 +1160,46 @@ static void r8168_mac_ocp_modify(struct rtl8169_private *tp, u32 reg, u16 mask, raw_spin_unlock_irqrestore(&tp->mac_ocp_lock, flags); } +static void r8127_sfp_sds_phy_reset(struct rtl8169_private *tp) +{ + RTL_W8(tp, 0x2350, RTL_R8(tp, 0x2350) & ~BIT(0)); + udelay(1); + + RTL_W16(tp, 0x233a, 0x801f); + RTL_W8(tp, 0x2350, RTL_R8(tp, 0x2350) | BIT(0)); + usleep_range(10, 20); +} + +static void r8127_sfp_init_10g(struct rtl8169_private *tp) +{ + int val; + + r8127_sfp_sds_phy_reset(tp); + + RTL_W16(tp, 0x233a, 0x801a); + RTL_W16(tp, 0x233e, (RTL_R16(tp, 0x233e) & ~0x3003) | 0x1000); + + r8168_phy_ocp_write(tp, 0xc40a, 0x0000); + r8168_phy_ocp_write(tp, 0xc466, 0x0003); + r8168_phy_ocp_write(tp, 0xc808, 0x0000); + r8168_phy_ocp_write(tp, 0xc80a, 0x0000); + + val = r8168_phy_ocp_read(tp, 0xc804); + r8168_phy_ocp_write(tp, 0xc804, (val & ~0x000f) | 0x000c); +} + +static void rtl_sfp_init(struct rtl8169_private *tp) +{ + if (tp->mac_version == RTL_GIGA_MAC_VER_80) + r8127_sfp_init_10g(tp); +} + +static void rtl_sfp_reset(struct rtl8169_private *tp) +{ + if (tp->mac_version == RTL_GIGA_MAC_VER_80) + r8127_sfp_sds_phy_reset(tp); +} + /* Work around a hw issue with RTL8168g PHY, the quirk disables * PHY MCU interrupts before PHY power-down. */ @@ -2308,6 +2354,36 @@ static void rtl8169_get_eth_ctrl_stats(struct net_device *dev, le32_to_cpu(tp->counters->rx_unknown_opcode); } +static int rtl8169_set_link_ksettings(struct net_device *ndev, + const struct ethtool_link_ksettings *cmd) +{ + struct rtl8169_private *tp = netdev_priv(ndev); + struct phy_device *phydev = tp->phydev; + int duplex = cmd->base.duplex; + int speed = cmd->base.speed; + + if (!tp->sfp_mode) + return phy_ethtool_ksettings_set(phydev, cmd); + + if (cmd->base.autoneg != AUTONEG_DISABLE) + return -EINVAL; + + if (!phy_check_valid(speed, duplex, phydev->supported)) + return -EINVAL; + + mutex_lock(&phydev->lock); + + phydev->autoneg = AUTONEG_DISABLE; + phydev->speed = speed; + phydev->duplex = duplex; + + rtl_sfp_init(tp); + + mutex_unlock(&phydev->lock); + + return 0; +} + static const struct ethtool_ops rtl8169_ethtool_ops = { .supported_coalesce_params = ETHTOOL_COALESCE_USECS | ETHTOOL_COALESCE_MAX_FRAMES, @@ -2327,7 +2403,7 @@ static const struct ethtool_ops rtl8169_ethtool_ops = { .get_eee = rtl8169_get_eee, .set_eee = rtl8169_set_eee, .get_link_ksettings = phy_ethtool_get_link_ksettings, - .set_link_ksettings = phy_ethtool_set_link_ksettings, + .set_link_ksettings = rtl8169_set_link_ksettings, .get_ringparam = rtl8169_get_ringparam, .get_pause_stats = rtl8169_get_pause_stats, .get_pauseparam = rtl8169_get_pauseparam, @@ -2435,6 +2511,9 @@ static void rtl8169_init_phy(struct rtl8169_private *tp) tp->pci_dev->subsystem_device == 0xe000) phy_write_paged(tp->phydev, 0x0001, 0x10, 0xf01b); + if (tp->sfp_mode) + rtl_sfp_init(tp); + /* We may have called phy_speed_down before */ phy_speed_up(tp->phydev); @@ -4800,6 +4879,10 @@ static void rtl8169_down(struct rtl8169_private *tp) phy_stop(tp->phydev); + /* Reset SerDes PHY to bring down fiber link */ + if (tp->sfp_mode) + rtl_sfp_reset(tp); + rtl8169_update_counters(tp); pci_clear_master(tp->pci_dev); @@ -5459,13 +5542,11 @@ static int rtl_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) } tp->aspm_manageable = !rc; - /* Fiber mode on RTL8127AF isn't supported */ if (rtl_is_8125(tp)) { u16 data = r8168_mac_ocp_read(tp, 0xd006); if ((data & 0xff) == 0x07) - return dev_err_probe(&pdev->dev, -ENODEV, - "Fiber mode not supported\n"); + tp->sfp_mode = true; } tp->dash_type = rtl_get_dash_type(tp); -- 2.52.0