The Marvell 88SM9705 is a 1-to-5 SATA port multiplier with one additional SEMB (SATA Enclosure Management Bridge) port [1]. Ports 0-4 are device ports and port 5 is the SEMB. The number of fan-out ports in GSCR[2] is 6 when the SEMB is enabled and 5 when it is not, so on boards without the SEMB there is no link 5 and this quirk does nothing. That includes the common 8-port PCIe cards that pair an 88SE9215 with an 88SM9705, which report 5 ports. The SEMB port never answers SRST. libata probes it like a device port, and every EH round on the PMP ends in a retry loop that lasts about a minute before EH gives up, then starts over: ata19.15: Port Multiplier 1.2, 0x1b4b:0x9705 r160, 6 ports, feat 0x1/0x1f ata19.05: hard resetting link ata19.05: failed to resume link (SControl 0) ata19.05: softreset failed (1st FIS failed) ata19.05: hard resetting link ... ata20.05: reset failed, giving up Disk discovery waits for this, including disks on other controllers. libata.force only partly works around it. The "disable" horkage only takes effect after IDENTIFY, which the SEMB link never reaches. "norst" on port 5 stops the retry loop, but the disks still come up about a minute later than with this change (see below). Treat port 5 the same way as port 4 of the Marvell 88SM4140 and mark the link ATA_LFLAG_DISABLED. Tested on a Synology DX1222 expansion unit (four 88SM9705 r160 behind a Marvell 88SE9235, passed through to a KVM guest, 6 disks), 7.4-rc1 with and without this change, one boot each: softreset reset failed, last disk failed giving up attached 7.4-rc1, no libata.force 60 12 197 s 7.4-rc1, libata.force=N.05:norst 0 0 70 s 7.4-rc1 + this patch, no force 0 0 11 s The problem was first found on a Synology DX1215 with the same chain, where this change brought the disks up after about 20 s instead of about 200 s, including a disk on a separate AHCI controller. Each PMP still logs one "failed to resume link (SControl 0)" for port 5 at probe time. Link: https://www.marvell.com/content/dam/marvell/en/public-collateral/storage/marvell-storage-88sm9705-functional-specifications-2015-06.pdf [1] Cc: stable@vger.kernel.org Tested-by: Kyrylo Biryuk Signed-off-by: Marco Ziliani --- I don't have this hardware myself: the problem was found and measured on a DX1215 by a user who preferred not to send the patch, and Kyrylo has since tested it on his DX1222. I used an AI coding assistant to draft the patch and the changelog; I reviewed them and can answer for them. --- Changes in v2: - Say that libata.force "norst" only partly works around the problem (Niklas). - Use Kyrylo's 7.4-rc1 results on a DX1222 as the test data, and drop the references to the downstream distribution (Niklas). - Mention the DX1222 in the comment. - Add Kyrylo's Tested-by. - Link to v1: https://patch.msgid.link/20261028-pmp-88sm9705-v1-1-cf951fe74573@gmail.com --- drivers/ata/libata-pmp.c | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/drivers/ata/libata-pmp.c b/drivers/ata/libata-pmp.c index 904f418387..43991e54eb 100644 --- a/drivers/ata/libata-pmp.c +++ b/drivers/ata/libata-pmp.c @@ -482,6 +482,20 @@ static void sata_pmp_quirks(struct ata_port *ap) if (link->pmp == 4) link->flags |= ATA_LFLAG_DISABLED; } + } else if (vendor == 0x1b4b && devid == 0x9705) { + /* + * Marvell 88SM9705 quirks + * + * 1-to-5 PMP with an extra SEMB port. It reports 6 ports and + * port 5 is the SEMB, which never answers SRST: EH spends about + * a minute per round retrying it, and disk discovery waits for + * that. Seen behind a Marvell 88SE9235 in the Synology DX1215 + * and DX1222. + */ + ata_for_each_link(link, ap, EDGE) { + if (link->pmp == 5) + link->flags |= ATA_LFLAG_DISABLED; + } } } --- base-commit: fb2c3f44a7e14627b9dca8e6b568e6cdc234b40b change-id: 20261028-pmp-88sm9705-2f741b435f16 Best regards, -- Marco Ziliani