If HW is RSC capable, it cannot add dummy bytes at the start of IP
packets. Alignment (ie number of dummy bytes) is configured using the
RBOF field inside the NCFGR register.

On the software side, the skb_reserve(skb, NET_IP_ALIGN) call must only
be done if those dummy bytes are added by the hardware; notice the
skb_reserve() is done AFTER writing the address to the device.

We cannot do the skb_reserve() call BEFORE writing the address because
the address field ignores the low 2/3 bits. Conclusion: in some cases,
we risk not being able to respect the NET_IP_ALIGN value (which is
picked based on unaligned CPU access performance).

Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
---
 drivers/net/ethernet/cadence/macb.h      |  3 +++
 drivers/net/ethernet/cadence/macb_main.c | 23 ++++++++++++++++++++---
 2 files changed, 23 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h
index 5b7d4cdb204d..93e8dd092313 100644
--- a/drivers/net/ethernet/cadence/macb.h
+++ b/drivers/net/ethernet/cadence/macb.h
@@ -537,6 +537,8 @@
 /* Bitfields in DCFG6. */
 #define GEM_PBUF_LSO_OFFSET			27
 #define GEM_PBUF_LSO_SIZE			1
+#define GEM_PBUF_RSC_OFFSET			26
+#define GEM_PBUF_RSC_SIZE			1
 #define GEM_PBUF_CUTTHRU_OFFSET			25
 #define GEM_PBUF_CUTTHRU_SIZE			1
 #define GEM_DAW64_OFFSET			23
@@ -775,6 +777,7 @@
 #define MACB_CAPS_MACB_IS_GEM			BIT(20)
 #define MACB_CAPS_DMA_64B			BIT(21)
 #define MACB_CAPS_DMA_PTP			BIT(22)
+#define MACB_CAPS_RSC				BIT(23)
 
 /* LSO settings */
 #define MACB_LSO_UFO_ENABLE			0x01
diff --git a/drivers/net/ethernet/cadence/macb_main.c b/drivers/net/ethernet/cadence/macb_main.c
index 39673f5c3337..be3d0c2313a1 100644
--- a/drivers/net/ethernet/cadence/macb_main.c
+++ b/drivers/net/ethernet/cadence/macb_main.c
@@ -1300,8 +1300,19 @@ static void gem_rx_refill(struct macb_queue *queue)
 			dma_wmb();
 			macb_set_addr(bp, desc, paddr);
 
-			/* properly align Ethernet header */
-			skb_reserve(skb, NET_IP_ALIGN);
+			/* Properly align Ethernet header.
+			 *
+			 * Hardware can add dummy bytes if asked using the RBOF
+			 * field inside the NCFGR register. That feature isn't
+			 * available if hardware is RSC capable.
+			 *
+			 * We cannot fallback to doing the 2-byte shift before
+			 * DMA mapping because the address field does not allow
+			 * setting the low 2/3 bits.
+			 * It is 3 bits if HW_DMA_CAP_PTP, else 2 bits.
+			 */
+			if (!(bp->caps & MACB_CAPS_RSC))
+				skb_reserve(skb, NET_IP_ALIGN);
 		} else {
 			desc->ctrl = 0;
 			dma_wmb();
@@ -2773,7 +2784,11 @@ static void macb_init_hw(struct macb *bp)
 	macb_set_hwaddr(bp);
 
 	config = macb_mdc_clk_div(bp);
-	config |= MACB_BF(RBOF, NET_IP_ALIGN);	/* Make eth data aligned */
+	/* Make eth data aligned.
+	 * If RSC capable, that offset is ignored by HW.
+	 */
+	if (!(bp->caps & MACB_CAPS_RSC))
+		config |= MACB_BF(RBOF, NET_IP_ALIGN);
 	config |= MACB_BIT(DRFCS);		/* Discard Rx FCS */
 	if (bp->caps & MACB_CAPS_JUMBO)
 		config |= MACB_BIT(JFRAME);	/* Enable jumbo frames */
@@ -4321,6 +4336,8 @@ static void macb_configure_caps(struct macb *bp,
 		dcfg = gem_readl(bp, DCFG2);
 		if ((dcfg & (GEM_BIT(RX_PKT_BUFF) | GEM_BIT(TX_PKT_BUFF))) == 0)
 			bp->caps |= MACB_CAPS_FIFO_MODE;
+		if (GEM_BFEXT(PBUF_RSC, gem_readl(bp, DCFG6)))
+			bp->caps |= MACB_CAPS_RSC;
 		if (gem_has_ptp(bp)) {
 			if (!GEM_BFEXT(TSU, gem_readl(bp, DCFG5)))
 				dev_err(&bp->pdev->dev,

-- 
2.51.1