Convert glue driver for Loongson DWMAC controller to use the generic platform suspend/resume routines for PCI controllers, instead of implementing its own one. Signed-off-by: Yao Zi --- drivers/net/ethernet/stmicro/stmmac/Kconfig | 1 + .../ethernet/stmicro/stmmac/dwmac-loongson.c | 36 ++----------------- 2 files changed, 4 insertions(+), 33 deletions(-) diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig index 598bc56edd8d..4b6911c62e6f 100644 --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig @@ -373,6 +373,7 @@ config DWMAC_LOONGSON default MACH_LOONGSON64 depends on (MACH_LOONGSON64 || COMPILE_TEST) && STMMAC_ETH && PCI depends on COMMON_CLK + depends on STMMAC_LIBPCI help This selects the LOONGSON PCI bus support for the stmmac driver, Support for ethernet controller on Loongson-2K1000 SoC and LS7A1000 bridge. diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c index 2a3ac0136cdb..584dc4ff8320 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c @@ -8,6 +8,7 @@ #include #include #include "stmmac.h" +#include "stmmac_libpci.h" #include "dwmac_dma.h" #include "dwmac1000.h" @@ -525,37 +526,6 @@ static int loongson_dwmac_fix_reset(struct stmmac_priv *priv, void __iomem *ioad 10000, 2000000); } -static int loongson_dwmac_suspend(struct device *dev, void *bsp_priv) -{ - struct pci_dev *pdev = to_pci_dev(dev); - int ret; - - ret = pci_save_state(pdev); - if (ret) - return ret; - - pci_disable_device(pdev); - pci_wake_from_d3(pdev, true); - return 0; -} - -static int loongson_dwmac_resume(struct device *dev, void *bsp_priv) -{ - struct pci_dev *pdev = to_pci_dev(dev); - int ret; - - pci_restore_state(pdev); - pci_set_power_state(pdev, PCI_D0); - - ret = pci_enable_device(pdev); - if (ret) - return ret; - - pci_set_master(pdev); - - return 0; -} - static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id *id) { struct plat_stmmacenet_data *plat; @@ -600,8 +570,8 @@ static int loongson_dwmac_probe(struct pci_dev *pdev, const struct pci_device_id plat->bsp_priv = ld; plat->setup = loongson_dwmac_setup; plat->fix_soc_reset = loongson_dwmac_fix_reset; - plat->suspend = loongson_dwmac_suspend; - plat->resume = loongson_dwmac_resume; + plat->suspend = stmmac_pci_plat_suspend; + plat->resume = stmmac_pci_plat_resume; ld->dev = &pdev->dev; ld->loongson_id = readl(res.addr + GMAC_VERSION) & 0xff; -- 2.51.2